MC56F8035V

MC56F8035V Allgemeine Beschreibung

The MC56F8035V is a microcontroller from NXP Semiconductors. It is part of the MC56F8000 series and features a 16-bit digital signal controller (DSC) core. The MC56F8035V includes peripherals and interfaces that are commonly used in embedded control applications.

Funktionen

• Digital Signal Controller Core
• Efficient 16-bit 56800E family Digital Signal Controller (DSC) engine with dual Harvard architecture
• As many as 32 Million Instructions Per Second (MIPS) at 32MHz core frequency
• Single-cycle 16 × 16-bit parallel Multiplier-Accumulator (MAC)
• Four 36-bit accumulators, including extension bits
• 32-bit arithmetic and logic multi-bit shifter
• Parallel instruction set with unique DSP addressing modes
• Hardware DO and REP loops
• Three internal address buses
• Four internal data buses
• Instruction set supports both DSP and controller functions
• Controller-style addressing modes and instructions for compact code
• Efficient C compiler and local variable support
• Software subroutine and interrupt stack with depth limited only by memory
• JTAG/Enhanced On-Chip Emulation (OnCE) for unobtrusive, processor speed-independent real-time debugging
• Memory
• Dual Harvard architecture permits as many as three simultaneous accesses to program and data memory
• Flash security and protection that prevent unauthorized users from gaining access to the internal Flash
• On-chip memory
• — 64KB of Program Flash (56F80235 device)
• 32KB of Program Flash (56F8025 device)
• — 8KB of Unified Data/Program RAM (56F8035 device)
• 4KB of Unified Data/Program RAM (56F8025 device)
• EEPROM emulation capability using Flash
• Peripheral Circuits for 56F8035/56F8025
• One multi-function six-output Pulse Width Modulator (PWM) module
• — Up to 96MHz PWM operating clock
• — 15 bits of resolution
• — Center-aligned and edge-aligned PWM signal mode
• — Four programmable fault inputs with programmable digital filter
• — Double-buffered PWM registers
• — Each complementary PWM signal pair allows selection of a PWM supply source from:
• – PWM generator
• – External GPIO
• – Internal timers
• – Analog comparator outputs
• – ADC conversion result which compares with values of ADC high- and low-limit registers to set PWM output
• Two independent 12-bit Analog-to-Digital Converters (ADCs)
• — 2 x 4 channel inputs
• — Supports both simultaneous and sequential conversions
• — ADC conversions can be synchronized by both PWM and timer modules
• — Sampling rate up to 2.67MSPS
• — 16-word result buffer registers
• Two internal 12-bit Digital-to-Analog Converters (DACs)
• — 2 microsecond settling time when output swing from rail to rail
• — Automatic waveform generation generates square, triangle and sawtooth waveforms with
• programmable period, update rate, and range
• One 16-bit multi-purpose Quad Timer module (TMR)
• — Up to 96MHz operating clock
• — Eight independent 16-bit counter/timers with cascading capability
• — Each timer has capture and compare capability
• — Up to 12 operating modes
• One Queued Serial Communication Interface (QSCI) with LIN Slave functionality
• — Full-duplex or single-wire operation
• — Two receiver wake-up methods:
• – Idle line
• – Address mark
• — Four-bytes-deep FIFOs are available on both transmitter and receiver
• One Queued Serial Peripheral Interfaces (QSPI)
• — Full-duplex operation
• — Master and slave modes
• — Four-words-deep FIFOs available on both transmitter and receiver
• — Programmable Length Transactions (2 to 16 bits)
• One Inter-Integrated Circuit (I2C) port
• — Operates up to 400kbps
• — Supports both master and slave operation
• — Supports both 10-bit address mode and broadcasting mode
• Three 16-bit Programmable Interval Timers (PITs)
• Two analog Comparators (CMPs)
• — Selectable input source includes external pins, DACs
• — Programmable output polarity
• — Output can drive Timer input, PWM fault input, PWM source, external pin output and trigger ADCs
• — Output falling and rising edge detection able to generate interrupts
• Computer Operating Properly (COP)/Watchdog timer capable of selecting different clock sources
• Up to 35 General-Purpose I/O (GPIO) pins with 5V tolerance
• Integrated Power-On Reset (POR) and Low-Voltage Interrupt (LVI) module
• Phase Lock Loop (PLL) provides a high-speed clock to the core and peripherals
• Clock sources:
• — On-chip relaxation oscillator
• — External clock: Crystal oscillator, ceramic resonator, and external clock source
• JTAG/EOnCE debug programming interface for real-time debugging
• Energy Information
• Fabricated in high-density CMOS with 5V tolerance
• On-chip regulators for digital and analog circuitry to lower cost and reduce noise
• Wait and Stop modes available
• ADC smart power management
• Each peripheral can be individually disabled to save power

Anwendung

• The MC56F8035V is suitable for a wide range of applications, including:
• Motor control systems
• Power management applications
• Industrial automation
• Sensor interfacing and data acquisition
• Consumer electronics

Spezifikationen