P89LPC935FA

P89LPC935FA Allgemeine Beschreibung

General descriptionThe P89LPC933/934/935/936 is a single-chip microcontroller, available in low cost packages, based on a high performance processor architecture that executes instructions in two to four clocks, six times the rate of standard 80C51 devices. Many system-level functions have been incorporated into the P89LPC933/934/935/936 in order to reduce component count, board space, and system cost.FeaturesPrincipal features■ 4 kB/8 kB/16 kB byte-erasable flash code memory organized into 1 kB/2 kB sectors   and 64-byte pages. Single-byte erasing allows any byte(s) to be used as non-volatile   data storage.■ 256-byte RAM data memory. Both the P89LPC935 and P89LPC936 also include a   512-byte auxiliary on-chip RAM.■ 512-byte customer data EEPROM on chip allows serialization of devices, storage of   setup parameters, etc. (P89LPC935/936).■ Dual 4-input multiplexed 8-bit A/D converters/DAC outputs (P89LPC935/936, single   A/D on P89LPC933/934).Two analog comparators with selectable inputs and   reference source.■ Two 16-bit counter/timers (each may be configured to toggle a port output upon timer   overflow or to become a PWM output) and a 23-bit system timer that can also be used   as an RTC.■ Enhanced UART with fractional baud rate generator, break detect, framing error   detection, and automatic address detection; 400 kHz byte-wide I2C-bus   communication port and SPI communication port.■ Capture/Compare Unit (CCU) provides PWM, input capture, and output compare   functions (P89LPC935/936).■ High-accuracy internal RC oscillator option allows operation without external oscillator   components.The RC oscillator option is selectable and fine tunable.■ 2.4 V to 3.6 V VDD operating range. I/O pins are 5 V tolerant (may be pulled up or   driven to 5.5 V).■ 28-pin TSSOP, PLCC, and HVQFN packages with 23 I/O pins minimum and up to 26   I/O pins while using on-chip oscillator and reset options.  Additional features■ A high performance 80C51 CPU provides instruction cycle times of 111 ns to 222 ns   for all instructions except multiply and divide when executing at 18 MHz. This is six   times the performance of the standard 80C51 running at the same clock frequency. A   lower clock frequency for the same performance results in power savings and reduced   EMI.■ Serial flash In-Circuit Programming (ICP) allows simple production coding with   commercial EPROM programmers. Flash security bits prevent reading of sensitive   application programs.■ Serial flash In-System Programming (ISP) allows coding while the device is mounted   in the end application.■ In-Application Programming (IAP) of the flash code memory. This allows changing the   code in a running application.■ Watchdog timer with separate on-chip oscillator, requiring no external components.   The watchdog prescaler is selectable from eight values.■ Low voltage reset (brownout detect) allows a graceful system shutdown when power   fails. May optionally be configured as an interrupt.■ Idle and two different power-down reduced power modes. Improved wake-up from   Power-down mode (a LOW interrupt input starts execution). Typical power-down   current is 1 µA (total power-down with voltage comparators disabled).■ Active-LOW reset. On-chip power-on reset allows operation without external reset   components. A reset counter and reset glitch suppression circuitry prevent spurious   and incomplete resets. A software reset function is also available.■ Configurable on-chip oscillator with frequency range options selected by user   programmed flash configuration bits. Oscillator options support frequencies from   20 kHz to the maximum operating frequency of 18 MHz.■ Oscillator fail detect. The watchdog timer has a separate fully on-chip oscillator   allowing it to perform an oscillator fail detect function.■ Programmable port output configuration options: quasi-bidirectional, open drain,   push-pull, input-only.■ Port ‘input pattern match’ detect. Port 0 may generate an interrupt when the value of   the pins match or do not match a programmable pattern.■ LED drive capability (20 mA) on all port pins. A maximum limit is specified for the   entire chip.■ Controlled slew rate port outputs to reduce EMI. Outputs have approximately 10 ns   minimum ramp times.■ Only power and ground connections are required to operate the   P89LPC933/934/935/936 when internal reset option is selected.■ Four interrupt priority levels.■ Eight keypad interrupt inputs, plus two additional external interrupt inputs.■ Schmitt trigger port inputs.■ Second data pointer.■ Emulation support.

Funktionen

• Principal features
• 4 kB/8 kB/16 kB byte-erasable flash code memory organized into 1 kB/2 kB sectors
• and 64-byte pages. Single-byte erasing allows any byte(s) to be used as non-volatile
• data storage.
• 256-byte RAM data memory. Both the P89LPC935 and P89LPC936 also include a
• 512-byte auxiliary on-chip RAM.
• 512-byte customer data EEPROM on chip allows serialization of devices, storage of
• setup parameters, etc. (P89LPC935/936).
• Dual 4-input multiplexed 8-bit A/D converters/DAC outputs (P89LPC935/936, single
• A/D on P89LPC933/934).Two analog comparators with selectable inputs and
• reference source.
• Two 16-bit counter/timers (each may be configured to toggle a port output upon timer
• overflow or to become a PWM output) and a 23-bit system timer that can also be used
• as an RTC.
• Enhanced UART with fractional baud rate generator, break detect, framing error
• detection, and automatic address detection; 400 kHz byte-wide I2C-bus
• communication port and SPI communication port.
• Capture/Compare Unit (CCU) provides PWM, input capture, and output compare
• functions (P89LPC935/936).
• High-accuracy internal RC oscillator option allows operation without external oscillator
• components. The RC oscillator option is selectable and fine tunable.
• 2.4 V to 3.6 V VDD operating range. I/O pins are 5 V tolerant (may be pulled up or
• driven to 5.5 V).
• 28-pin TSSOP, PLCC, and HVQFN packages with 23 I/O pins minimum and up to 26
• I/O pins while using on-chip oscillator and reset options.
• Additional features
• A high performance 80C51 CPU provides instruction cycle times of 111 ns to 222 ns
• for all instructions except multiply and divide when executing at 18 MHz. This is six
• times the performance of the standard 80C51 running at the same clock frequency. A
• lower clock frequency for the same performance results in power savings and reduced
• EMI.
• Serial flash In-Circuit Programming (ICP) allows simple production coding with
• commercial EPROM programmers. Flash security bits prevent reading of sensitive
• application programs.
• Serial flash In-System Programming (ISP) allows coding while the device is mounted
• in the end application.
• In-Application Programming (IAP) of the flash code memory. This allows changing the
• code in a running application.
• Watchdog timer with separate on-chip oscillator, requiring no external components.
• The watchdog prescaler is selectable from eight values.
• Low voltage reset (brownout detect) allows a graceful system shutdown when power
• fails. May optionally be configured as an interrupt.
• Idle and two different power-down reduced power modes. Improved wake-up from
• Power-down mode (a LOW interrupt input starts execution). Typical power-down
• current is 1 μA (total power-down with voltage comparators disabled).
• Active-LOW reset. On-chip power-on reset allows operation without external reset
• components. A reset counter and reset glitch suppression circuitry prevent spurious
• and incomplete resets. A software reset function is also available.
• Configurable on-chip oscillator with frequency range options selected by user
• programmed flash configuration bits. Oscillator options support frequencies from
• 20 kHz to the maximum operating frequency of 18 MHz.
• Oscillator fail detect. The watchdog timer has a separate fully on-chip oscillator
• allowing it to perform an oscillator fail detect function.
• Programmable port output configuration options: quasi-bidirectional, open drain,
• push-pull, input-only.
• Port ‘input pattern match’ detect. Port 0 may generate an interrupt when the value of
• the pins match or do not match a programmable pattern.
• LED drive capability (20 mA) on all port pins. A maximum limit is specified for the
• entire chip.
• Controlled slew rate port outputs to reduce EMI. Outputs have approximately 10 ns
• minimum ramp times.
• Only power and ground connections are required to operate the
• P89LPC933/934/935/936 when internal reset option is selected.
• Four interrupt priority levels.
• Eight keypad interrupt inputs, plus two additional external interrupt inputs.
• Schmitt trigger port inputs.
• Second data pointer.
• Emulation support.

Spezifikationen